SHOW DISKS displays the following information on
                      all available physical disks:

                      - Disk number

                      - Enclosure bus number and ID

                      - Disk size

                      - UNIT created on the disk

                      - Disks assigned as spares

                      Note:
                            - SHOW DISK <disk_n> can be used to see
                              information of a particular disk,
                              where disk_n is the disk number. Disks
                              are identified by their corresponding
                              SCSI bus and SCSI IDs for all the controllers.
                              For SAS controllers, internally connected
                              disks are numbered based on their bay numbers
                              and externally connected disks are numbered
                              based on combination of their box number
                              and bay number as
                              "disk_n" = box Number *100 + bay number".

                              Examples
                              For SAS controllers, the output of
                              SHOW DISK command is as follows:

                              MSA> SHOW DISK 1

                              SAS device                  [Disk]
                              Disk 1: bus: 1, Target id: 7, Port: 3I,
                              Box/Enclosure: 1, Bay: 1,
                              size 68.37 [73.41]GB
                              Disk 1, # 0, size 14329984 blocks,
                              (6.83 [7.34] GB), Unit 3.
                              Disk 1, # 1, size 128979218 blocks,
                              (61.50 [66.04] GB), Unused.

                              MSA> SHOW DISK 201

                              SATA device                  [Disk]
                              Disk 201: bus: 1, Target id: 8, Port: 2E,
                              Box/Enclosure: 2, Bay: 1,
                              size 149.05 [160.04]GB
                              Disk 201, # 0, size 312516272 blocks,
                              (149.02 [160.01] GB), Unused.
                              MSA>

                              For all other controllers, the output of
                              SHOW DISK command is as follows:

                              MSA> SHOW DISK 9

                              SAS device                      [Disk]
                              Disk 9: bus: 1, Target id: 9, Port: 1E,
                              Box/Enclosure: 2, Bay: 5,  size 68.37 [73.41]GB
                              Disk 9, # 0, size 2096640 blocks,
                              (1023.75 [1073.48] MB), Unit 1.
                              Disk 9, # 1, size 1397664 blocks,
                              (682.45 [715.60] MB), Unit 2.
                              Disk 9, # 2, size 1044256 blocks,
                              (509.89 [534.66] MB), Unit 3.
                              Disk 9, # 3, size 1048320 blocks,
                              (511.88 [536.74] MB), Unit 4.
                              Disk 9, # 4, size 137722322 blocks,
                              (65.67 [70.51] GB), Unused.
                              MSA>

                           - For Smart Array P400 series of controllers,
                             the Target id, Connector and BAY are also
                             displayed.

                      Format:
                              SHOW DISKS / <qualifiers>

1  –  Parameters

                     None

2  –  Qualifiers

2.1    /AVAILABLE

                    Lists all the disks on which there are no units
                    configured.

2.2    /ENCLOSURE

                    Displays all the disks connected to a particular
                    enclosure.

                    Note: Supported only for SAS controllers.

                    Format:
                             SHOW DISKS/ENCLOSURE = <enclosure_n>

2.3    /FULL

                    Displays the drive model and the drive serial number
                    in addition to the disk information.

                    Note: For Smart Array P400 series of controllers, the
                          following information is displayed:

                          - Connector Location
                          - Connector
                          - Enclosure
                          - Bay
                          - WWID
                          - Device Type
                          - Disk Capacity
                          - Device Status
                          - Device Vendor ID
                          - Device Product ID
                          - Device Serial Number
                          - Device Firmware Version
                          - Reserved Area (cfg/status information)
                          - Block Size (bytes/sector)
                          - M&P Data Stamped
                          - Last Failure Reason
                          - Physical Disk Flags

2.4    /MEMBER

                    Displays the disks on which the units are configured.

2.5    /SPARES

                    Displays the disks that are configured as spare for
                    logical units.

2.6    /VERBOSE

                    Provides logging that can be interpreted by engineering.

3  –  Examples

                    MSA> SHOW DISKS

                    Other Examples:

                    - SHOW DISK/SPARE
                    - SHOW DISK/AVAILABLE
                    - SHOW DISK/ENCLOSURE